The thesis with supervisor Prof. Gianluca Percoco and co-supervisor the PhD Gianni Stano and entitled "Design and characterization of electromagnetic actuators manufactured with 3D printing" had the purpose of designing and manufacturing an activator used by Additive Manufacturing techniques (AM) and in particular through Fused Filament Fabrication (FFF) technology and moved through electrical incision with unconventional gallium-based windings. Through the theoretical study of the numerous AM technologies and the various materials present, it was possible to determine the technique and materials most suited to the project to be created, opting for plastic filaments that can be printed by 3D FFF machines. Similarly, an in-depth theoretical study of the electromagnetic aspects made it possible to size the electric and magnetic forces to choose components (permanent magnet and windings) that satisfied the typical boundary conditions of unconventional actuation. Starting from a search of the existing literature, the merits, defects, limitations, as well as the current stage of progress in the field of unconventional implementation were understood. It was therefore decided to develop a linear actuator model based on the industrial motor called "ironcore", imitating its geometric characteristics and optimizing them in order to obtain an object as congenial as possible to production using AM techniques, orienting itself towards an automated design, repeatable, modular, low cost and implemented in a short time. The entire study involved 3 design / construction phases and a final test / measurement phase. In the design phases, various approaches were studied mainly related to three aspects: • Tribological aspect, linked to the geometry of the actuator, developing a concept of modularity. It was thus possible to act on the printing times, on the orientation of the print, on the geometry and on the frictions themselves, related to the material used and the process parameters involved. The actuator designed through CAD is composed of a slide (stator with permanent magnet), a carriage (sliding part on the slide), a rotor with microfluidic channels (in various configurations: modular and "single block"); ● Geometric aspect of microfluidic channels. The rotor consists of windings in unconventional material such as gallium (semiconductor with properties favorable to injection at room temperature) and has provided for the creation of channels inside which the semiconductor excited by the supply current flows (during operation). Then the geometries of the channels were studied in order to reach a shape that does not require supports, even reaching a toric limit of the section of the channels. The peculiarity is precisely a trapezoidal shape which does not require supports during printing and which at the same time does not deform when the nozzle passes during the deposition of the layre by layer material; ● Electromagnetic aspect, linked to the study of movement by electric excitation and iteration between a permeating magnetic field and one induced by the passage of current through the square gallium coils. Based on the principle of the electric motor and the Lorentz force (F = iBl), the desired movement was obtained. In the measurement phase, the actual movement of the component was calculated using an accelerometer and the physical-engineering performance of the actuator was evaluated, comparing it with a twin with copper windings and ascertaining its actual operation and expected behavior.

L’elaborato di tesi con Relatore il prof.re Gianluca Percoco e correlatore il PhD Gianni Stano e dal titolo “Progettazione e caratterizzazione di attuatori elettromagnetici fabbricati con stampa 3D” ha avuto il fine di progettare e realizzare un attuatore stampato mediante tecniche di Additive Manufacturing (AM) ed in particolar modo mediante tecnologia Fused Filament Fabrication (FFF) e movimentato attraverso eccitazione elettrica con avvolgimenti non convenzionali a base di Gallio. Attraverso lo studio teorico delle numerose tecnologie di AM e dei vari materiali presenti è stato possibile determinare la tecnica e i materiali più consoni al progetto da realizzare, optando per filamenti plastici printabili da macchine 3D FFF. Analogamente, un approfondito studio teorico degli aspetti elettromagnetici ha permesso di dimensionare le forze elettriche e magnetiche per scegliere componenti (magnete permanete e avvolgimenti) che soddisfacevano le condizioni al contorno tipiche dell’attuazione non convenzionale. Partendo da una ricerca della letteratura esistente, si sono compresi i pregi, i difetti, i limiti, nonché il punto di avanzamento attuale nell’ambito dell’attuazione non convenzionale. Si è quindi scelto di sviluppare un modello di attuatore lineare basato sul motore industriale detto “ironcore”, imitandone le caratteristiche geometriche e ottimizzandone le stesse per poter ottenere un oggetto il più congeniale possibile alla produzione mediante tecniche di AM, orientandosi verso una progettazione automatizzata, ripetibile, modulare, a basso costo e realizzata in tempi brevi. L’intero studio ha previsto 3 fasi di progettazione/realizzazione ed una fase finale di test/misurazione. Nelle fasi progettazione si sono studiati vari approcci legati principalmente a tre aspetti: • Aspetto tribologico, legato alla geometria dell’attuatore, sviluppando un concetto di modularità. È stato così possibile agire sui tempi di stampa, sull’orientazione della stampa, sulla geometria e sugli stessi attriti, legati al materiale utilizzato e ai parametri di processo in gioco. L’attuatore progettato attraverso CAD è composto da una slitta (statore con magnete permanente), un carrello (parte scorrevole sulla slitta), un rotore con canali microfluidici (in varie configurazioni: modulare e “a blocco unico”); ● Aspetto geometrico dei canali microfluidici. Il rotore è costituito da avvolgimenti in materiale non convenzionale quale Gallio (semiconduttore dalle proprietà favorevole all’iniezione a temperatura ambiente) e ha previsto la creazione di canali al cui interno scorre il semiconduttore eccitato dalla corrente di alimentazione (in fase di azionamento). Quindi si sono studiate le geometrie dei canali per poter giungere ad una forma tale da non richiedere supporti, arrivando anche ad un limite torico della sezione dei canali. La particolarità è proprio una forma trapezoidale che durante la stampa non richiede supporti e che allo stesso tempo non si deforma al passaggio del nozzle durante la deposizione del materiale layre by layer; ● Aspetto elettromagnetico, legato allo studio del movimento mediante eccitazione elettrica e iterazione tra un campo magnetico permeante ed uno indotto dal passaggio di corrente attraverso le spire quadrate in gallio. Basandosi sul principio del motore elettrico e della forza di Lorentz (F = iBl) si è ottenuto il movimento desiderato. Nella fase di misurazione, mediante un accelerometro è stato calcolato l’effettivo movimento del componente e si è valutata la prestazione fisico-ingegneristica dell’attuatore, confrontandolo con un gemello con avvolgimenti in rame e constatandone l’effettivo funzionamento e comportamento previsto.

PROGETTAZIONE E CARATTERIZZAZIONE DI ATTUATORI ELETTROMAGNETICI FABBRICATI CON STAMPA 3D

PAVONE, ANTONIO
2020/2021

Abstract

The thesis with supervisor Prof. Gianluca Percoco and co-supervisor the PhD Gianni Stano and entitled "Design and characterization of electromagnetic actuators manufactured with 3D printing" had the purpose of designing and manufacturing an activator used by Additive Manufacturing techniques (AM) and in particular through Fused Filament Fabrication (FFF) technology and moved through electrical incision with unconventional gallium-based windings. Through the theoretical study of the numerous AM technologies and the various materials present, it was possible to determine the technique and materials most suited to the project to be created, opting for plastic filaments that can be printed by 3D FFF machines. Similarly, an in-depth theoretical study of the electromagnetic aspects made it possible to size the electric and magnetic forces to choose components (permanent magnet and windings) that satisfied the typical boundary conditions of unconventional actuation. Starting from a search of the existing literature, the merits, defects, limitations, as well as the current stage of progress in the field of unconventional implementation were understood. It was therefore decided to develop a linear actuator model based on the industrial motor called "ironcore", imitating its geometric characteristics and optimizing them in order to obtain an object as congenial as possible to production using AM techniques, orienting itself towards an automated design, repeatable, modular, low cost and implemented in a short time. The entire study involved 3 design / construction phases and a final test / measurement phase. In the design phases, various approaches were studied mainly related to three aspects: • Tribological aspect, linked to the geometry of the actuator, developing a concept of modularity. It was thus possible to act on the printing times, on the orientation of the print, on the geometry and on the frictions themselves, related to the material used and the process parameters involved. The actuator designed through CAD is composed of a slide (stator with permanent magnet), a carriage (sliding part on the slide), a rotor with microfluidic channels (in various configurations: modular and "single block"); ● Geometric aspect of microfluidic channels. The rotor consists of windings in unconventional material such as gallium (semiconductor with properties favorable to injection at room temperature) and has provided for the creation of channels inside which the semiconductor excited by the supply current flows (during operation). Then the geometries of the channels were studied in order to reach a shape that does not require supports, even reaching a toric limit of the section of the channels. The peculiarity is precisely a trapezoidal shape which does not require supports during printing and which at the same time does not deform when the nozzle passes during the deposition of the layre by layer material; ● Electromagnetic aspect, linked to the study of movement by electric excitation and iteration between a permeating magnetic field and one induced by the passage of current through the square gallium coils. Based on the principle of the electric motor and the Lorentz force (F = iBl), the desired movement was obtained. In the measurement phase, the actual movement of the component was calculated using an accelerometer and the physical-engineering performance of the actuator was evaluated, comparing it with a twin with copper windings and ascertaining its actual operation and expected behavior.
2020
DESIGN AND CHARACTERIZATION OF ELECTROMAGNETIC ACTUATORS MANUFACTURED WITH 3D PRINTING
L’elaborato di tesi con Relatore il prof.re Gianluca Percoco e correlatore il PhD Gianni Stano e dal titolo “Progettazione e caratterizzazione di attuatori elettromagnetici fabbricati con stampa 3D” ha avuto il fine di progettare e realizzare un attuatore stampato mediante tecniche di Additive Manufacturing (AM) ed in particolar modo mediante tecnologia Fused Filament Fabrication (FFF) e movimentato attraverso eccitazione elettrica con avvolgimenti non convenzionali a base di Gallio. Attraverso lo studio teorico delle numerose tecnologie di AM e dei vari materiali presenti è stato possibile determinare la tecnica e i materiali più consoni al progetto da realizzare, optando per filamenti plastici printabili da macchine 3D FFF. Analogamente, un approfondito studio teorico degli aspetti elettromagnetici ha permesso di dimensionare le forze elettriche e magnetiche per scegliere componenti (magnete permanete e avvolgimenti) che soddisfacevano le condizioni al contorno tipiche dell’attuazione non convenzionale. Partendo da una ricerca della letteratura esistente, si sono compresi i pregi, i difetti, i limiti, nonché il punto di avanzamento attuale nell’ambito dell’attuazione non convenzionale. Si è quindi scelto di sviluppare un modello di attuatore lineare basato sul motore industriale detto “ironcore”, imitandone le caratteristiche geometriche e ottimizzandone le stesse per poter ottenere un oggetto il più congeniale possibile alla produzione mediante tecniche di AM, orientandosi verso una progettazione automatizzata, ripetibile, modulare, a basso costo e realizzata in tempi brevi. L’intero studio ha previsto 3 fasi di progettazione/realizzazione ed una fase finale di test/misurazione. Nelle fasi progettazione si sono studiati vari approcci legati principalmente a tre aspetti: • Aspetto tribologico, legato alla geometria dell’attuatore, sviluppando un concetto di modularità. È stato così possibile agire sui tempi di stampa, sull’orientazione della stampa, sulla geometria e sugli stessi attriti, legati al materiale utilizzato e ai parametri di processo in gioco. L’attuatore progettato attraverso CAD è composto da una slitta (statore con magnete permanente), un carrello (parte scorrevole sulla slitta), un rotore con canali microfluidici (in varie configurazioni: modulare e “a blocco unico”); ● Aspetto geometrico dei canali microfluidici. Il rotore è costituito da avvolgimenti in materiale non convenzionale quale Gallio (semiconduttore dalle proprietà favorevole all’iniezione a temperatura ambiente) e ha previsto la creazione di canali al cui interno scorre il semiconduttore eccitato dalla corrente di alimentazione (in fase di azionamento). Quindi si sono studiate le geometrie dei canali per poter giungere ad una forma tale da non richiedere supporti, arrivando anche ad un limite torico della sezione dei canali. La particolarità è proprio una forma trapezoidale che durante la stampa non richiede supporti e che allo stesso tempo non si deforma al passaggio del nozzle durante la deposizione del materiale layre by layer; ● Aspetto elettromagnetico, legato allo studio del movimento mediante eccitazione elettrica e iterazione tra un campo magnetico permeante ed uno indotto dal passaggio di corrente attraverso le spire quadrate in gallio. Basandosi sul principio del motore elettrico e della forza di Lorentz (F = iBl) si è ottenuto il movimento desiderato. Nella fase di misurazione, mediante un accelerometro è stato calcolato l’effettivo movimento del componente e si è valutata la prestazione fisico-ingegneristica dell’attuatore, confrontandolo con un gemello con avvolgimenti in rame e constatandone l’effettivo funzionamento e comportamento previsto.
Attuatori
elettromagnetici
Stampa 3D
Gallio
Lineari
File in questo prodotto:
File Dimensione Formato  
PAVONE_tesi.pdf

File consultabile da postazioni biblioteca

Descrizione: Tesi magistrale di Pavone Antonio
Dimensione 4.32 MB
Formato Adobe PDF
4.32 MB Adobe PDF

I documenti in UNITESI sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/20.500.14253/87323