The crankshaft converts the reciprocating motion of the pistons into useful torque and, throughout the life of the engine, is subjected to cyclic bending and torsional loads that make fatigue the governing design criterion, with the fillets between journals and webs as the critical locations. This thesis presents the finite element analysis and the static and fatigue assessment of the crankshaft of a small-displacement, spark-ignition, inline four-cylinder engine, modelled in Autodesk Inventor and analysed in ANSYS Workbench (Student version). The methodology was first validated on two geometries with an analytical reference: a stepped shaft under combined bending and torsion and a cylinder under internal pressure. The loads were derived from a cycle model with heat release described by the Wiebe function, at the instant of peak cylinder pressure and at an engine speed of 9000 rpm, assumed as the upper operating limit; gas and inertia forces were transmitted along the connecting-rod axis and distributed over the four crank throws according to the engine firing order. The model of the complete crankshaft, with the main bearings represented as deformable supports, was checked through the equilibrium between applied loads and reaction forces. The mesh convergence study revealed a numerical singularity along the tangency line between the fillet and the bearing surface, whereas inside the fillet, from about 1 mm away from the tangency line, the solution stabilises, whereas at P1, 0.17 mm from it, the reading is not converged to the level required by the standard. The critical location is the counterweight–main journal 2 fillet, with an equivalent stress of 134 MPa, a static safety factor of about 5.6 and a fatigue safety factor of about 1.8. The comparison with the analytical procedure of IACS UR M53 yields lower stresses at the critical fillet, while confirming the fatigue assessment: the hypothesis that the discrepancy stems from the statically determinate single-throw scheme of the standard is not supported by the equilibrium check, and the local effect of the support reaction and the position of the reading point remain to be separated.
L’albero a gomiti trasforma il moto alternativo dei pistoni in coppia utile ed è sollecitato, per l’intera vita del motore, da carichi ciclici di flessione e torsione che rendono la fatica il criterio di progetto dimensionante, con i raccordi tra perni e bracci come sedi critiche. La tesi presenta l’analisi agli elementi finiti e la verifica statica e a fatica dell’albero a gomiti di un motore a quattro cilindri in linea ad accensione comandata di piccola cilindrata, modellato in Autodesk Inventor e analizzato in ANSYS Workbench nella versione Student. La metodologia è stata dapprima validata su due geometrie con riferimento analitico, un albero a gradino in flessione e torsione e un cilindro in pressione. I carichi sono stati ricavati da un modello del ciclo con rilascio di calore secondo la legge di Wiebe, all’istante di massima pressione in camera e a un regime di 9000 giri/min, assunto come limite superiore di funzionamento; le forze dei gas e d’inerzia sono state trasmesse lungo l’asse della biella e ripartite sulle quattro manovelle secondo la fasatura del motore. Il modello dell’albero completo, con i supporti di banco schematizzati come appoggi deformabili, è stato verificato attraverso l’equilibrio tra carichi applicati e reazioni vincolari. Lo studio di convergenza ha mostrato una singolarità numerica sulla linea di tangenza tra raccordo e superficie di appoggio, mentre all’interno del raccordo, a partire da circa 1 mm dalla linea di tangenza, la soluzione si stabilizza, mentre in P1, a 0,17 mm, la lettura non è convergente al livello richiesto dalla norma. Il punto critico è il raccordo contrappeso–perno di banco 2, con una tensione equivalente di 134 MPa, un coefficiente di sicurezza statico di circa 5,6 e un coefficiente a fatica di circa 1,8. Il confronto con la procedura analitica IACS UR M53 fornisce tensioni inferiori al raccordo critico, pur confermando la verifica a fatica: l’ipotesi che lo scostamento dipenda dallo schema isostatico a manovella singola della norma non è sostenuta dall’equilibrio, e restano da separare l’effetto locale della reazione del supporto e la posizione del punto di lettura.
ANALISI FEM E VERIFICA STRUTTURALE E A FATICA DELL’ALBERO A GOMITI DI UN MOTORE A 4 CILINDRI
MEROTTA, IRENE
2025/2026
Abstract
The crankshaft converts the reciprocating motion of the pistons into useful torque and, throughout the life of the engine, is subjected to cyclic bending and torsional loads that make fatigue the governing design criterion, with the fillets between journals and webs as the critical locations. This thesis presents the finite element analysis and the static and fatigue assessment of the crankshaft of a small-displacement, spark-ignition, inline four-cylinder engine, modelled in Autodesk Inventor and analysed in ANSYS Workbench (Student version). The methodology was first validated on two geometries with an analytical reference: a stepped shaft under combined bending and torsion and a cylinder under internal pressure. The loads were derived from a cycle model with heat release described by the Wiebe function, at the instant of peak cylinder pressure and at an engine speed of 9000 rpm, assumed as the upper operating limit; gas and inertia forces were transmitted along the connecting-rod axis and distributed over the four crank throws according to the engine firing order. The model of the complete crankshaft, with the main bearings represented as deformable supports, was checked through the equilibrium between applied loads and reaction forces. The mesh convergence study revealed a numerical singularity along the tangency line between the fillet and the bearing surface, whereas inside the fillet, from about 1 mm away from the tangency line, the solution stabilises, whereas at P1, 0.17 mm from it, the reading is not converged to the level required by the standard. The critical location is the counterweight–main journal 2 fillet, with an equivalent stress of 134 MPa, a static safety factor of about 5.6 and a fatigue safety factor of about 1.8. The comparison with the analytical procedure of IACS UR M53 yields lower stresses at the critical fillet, while confirming the fatigue assessment: the hypothesis that the discrepancy stems from the statically determinate single-throw scheme of the standard is not supported by the equilibrium check, and the local effect of the support reaction and the position of the reading point remain to be separated.I documenti in UNITESI sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.
https://hdl.handle.net/20.500.14253/111183